Resin is a surface, not a structure. It bonds to whatever is underneath and then copies it: every crack, joint, wobble and damp patch in the base finds its way to the top sooner or later. So the real question behind "can resin go over this?" is whether what you have now is solid, dry and stuck down. Here is the answer for every base people ask us about, outside and in.
Every base at a glance
| What is down now | Answer | What it takes |
|---|---|---|
| Tarmac (driveway) | Yes | Sound, clean, dry. New tarmac needs anything from cooling to 7 days first, by system. |
| Concrete (driveway) | Yes, if sound | Cleaned and primed. Joints carried through the resin. Cracks repaired first. |
| Block paving, setts or flags | No | Lifted, then a tarmac or concrete base laid. |
| Old resin drive | Only if sound | A failed surface is planed off; the base under it can often stay. |
| Loose gravel | No | Dug out and a full base built. Compacted stone suits a foot path only. |
| Soil or grass | No | Excavated and a full sub-base and binder course built. |
| New concrete (floor) | Yes, once cured | Usually 4 weeks at least, one maker says 8 weeks. Moisture at 75% RH or below. |
| Ceramic or quarry tiles | Only if sound | Glaze ground off, hollow tiles replaced, grout lines filled, special primer. |
| Laminate, vinyl, carpet | No | Comes up. Resin goes on the floor underneath. |
| Timber or plywood | Only with the right system | Sound, clean, dry, waxes and coatings sanded off. |
| Old floor paint | It depends | A thin coating can go over well-bonded paint. A thicker resin system wants it removed. |
| Old epoxy floor | Yes, if bonded | Abraded to give a key, then recoated. |
The rest of this page takes each row in turn. Cracked concrete has its own page, because it has the most moving parts: our breakdown of putting resin over cracked concrete sorts hairline cracks from moving ones and covers damp coming up through the slab.
Resin-bound driveways: the bases that work
UK system makers agree on the short list. DALTEX names tarmac, asphalt and concrete, new or existing, and Natratex lists macadam, asphalt and concrete. Both want the surface clean, dry and free of contamination. DALTEX adds that there is no single preferred base, and that big, unbroken slabs with few joints give the best finish.
Over tarmac
Yes, and it is the easiest base there is. SureSet calls asphalt (tarmac) the ideal base and lays straight onto an existing one. The tarmac has to be sound and sit on a sub-base deep enough for the weight it will carry, so a drive that is already rutting under the car is telling you it needs more than a new top. Tar residue gets cleaned off with detergent and left to dry, and the whole drive is power washed, because DALTEX warns dust, dirt or moss will stop the resin bonding.
Freshly laid tarmac is where the makers part company. SureSet lays on new asphalt as soon as it has cooled. Ronacrete says leave it at least 24 hours at 20°C. DALTEX wants macadam at least 7 days old so it has fully cured. Whoever lays your drive should follow the system they are using, and if you are having new tarmac laid first, ask which one.
Over concrete
Yes, if it is structurally sound. DALTEX calls concrete a difficult surface to bond to, so DALTEX and SureSet both prime it first, and SureSet advises a crack reduction membrane on every concrete base as well. Expansion joints in the slab are not buried: DALTEX and SureSet both carry them up through the resin surface, because a slab that moves at a joint will crack whatever is laid over it.
New concrete again depends on the system. SureSet allows a minimum of 7 days; DALTEX says ideally 28 days so it has fully cured. SureSet is blunt about the risk on any concrete base: the resin is crack resistant, but it will ultimately reflect any crack in the base. Cracks are cut out and repaired before laying, as our cracked concrete page explains.
Drainage over an old base
Resin-bound driveways: the bases that do not
Block paving, setts and flags
No. DALTEX says paving bases such as block paving, setts or flags are not suitable, because all the joints below the surface would ultimately lead to cracks in the resin. Natratex says the same: block paving does not give a stable enough base. The blocks come up and a tarmac or concrete base goes down. If you are still choosing between the two surfaces, our resin driveway vs block paving comparison sets them side by side.
Loose gravel
You cannot pour resin over a gravel drive. DALTEX says resin surfacing cannot usually be laid on a granular base, the exception being tree pits, and warns that damp coming up through it can affect the resin. Loose gravel is the weakest version of that: nothing is holding the stones still.
There is one narrow case where stone does work. DALTEX allows compacted MOT Type 3 for foot traffic only. SureSet allows crushed stone for low pedestrian traffic with no vehicles, built in two layers of 4/20 free-draining stone compacted to at least 100 mm, with the resin laid at 30 mm or more to make up for the weaker base. That suits a garden path. It does not suit a drive. For a car, the gravel is dug out and a full base is built, and our resin driveway vs gravel page weighs up whether that is worth it.
Soil and grass
No. Natratex lists soil and grass alongside block paving as bases resin bound cannot be laid on, because neither gives enough support. A new drive over a lawn or a dug-out front garden is a full construction job, built up layer by layer as in the next section.
An old resin drive
Only if it is still sound. DALTEX says any existing surface must be sound and free of cracks, and the resin will only ever be as stable as what it sits on. Where an old resin drive has failed, the usual fix is to remove the surface and keep the base. SureSet describes one drive that had ravelled, cracked and gone uneven: the faulty surface was planed off, taking care not to damage the tarmac below, which was still in good condition, and new resin bound was laid over it at 18 mm. A small damaged patch on an otherwise good drive can often be repaired instead, and our page on resin driveway repairs covers when to patch and when to resurface.
What goes under a resin driveway
When there is no usable base, one is built. Ronacrete publishes a full suggested build-up for its RonaDeck resin-bound system, and it is a good picture of what sits under a properly laid drive, from the top down:
| Layer | Footpath | Driveway | Car park |
|---|---|---|---|
| Resin-bound surface | 15 mm minimum | 15 mm minimum | 18 mm minimum |
| Binder course (AC14 open graded asphalt) | 50 mm minimum | 60 mm minimum | 90 mm minimum |
| Type 3 granular sub-base, well compacted | 175 mm minimum | 200 mm minimum | 300 mm minimum |
| Geotextile or membrane | Optional | Optional | Optional |
| Capping layer | If the ground needs it | If the ground needs it | If the ground needs it |
Two parts of that stack are easy to miss. DALTEX describes a porous base as open textured macadam on Type 3 stone, so the whole drive stays permeable from top to bottom rather than letting water through the resin only to sit on a solid layer underneath. The geotextile, in Ronacrete's words, is there to stop soil migrating up into the stone. Where the water cannot soak away, an impermeable membrane carries it to an infiltration or storage system instead. Ronacrete is clear that these are suggested figures: the build-up has to suit the traffic and the ground on your site.
Surface depth matters too. DALTEX sets 18 mm as the minimum for its BBA approved installations, with 15 mm allowed on a footpath, and SureSet usually lays between 12 mm and 24 mm depending on the stone size and use. A new base also needs a firm edge: DALTEX sets kerbs or blocks to stand 18 mm above the base and advises against edging up against a fence or gravel board, which can move later and disturb the resin. Our page on driveway edging covers the options.
The cost gap is real. Published UK cost ranges put resin bound over a sound base at £40-£70 per m², and digging out and laying a new sub-base adds £25-£45 per m² on top (market ranges, checked 2026-11-05). Our resin driveway cost page breaks the numbers down.
Not sure your drive can take resin as it is?
Tell us what is down now, tarmac, concrete, blocks or gravel, and roughly how big it is. We will say whether it goes straight over or needs a new base, and quote for exactly that.
Thinking of doing it yourself? The base decides the job either way, and our page on a DIY resin driveway goes through what a homeowner can realistically take on.
Resin floors: what they can go over
Indoors the rules are stricter, because a resin floor is far thinner than a driveway and it is bonded right across its whole area. Every maker's data sheet asks for the same three things: a base that is sound, clean and dry. What changes is how each base gets there.
Concrete, and how long new concrete needs
Concrete is the natural base for a resin floor, once it has cured and dried out. New concrete holds a lot of water, and moisture trapped under resin pushes it off. The waits on UK data sheets:
- KDR: at least 28 days old, with moisture at 75% RH or below.
- Virtus Resins: at least 4 weeks old, or moisture under 5%.
- Watco: roughly eight weeks to dry for its fast-cure coating.
Age alone does not settle it, which is why the makers set a moisture figure as well as a date. Above 75% RH, KDR specifies a damp proof membrane first. A quick DIY check from Rust-Oleum: tape a sheet of plastic to the floor overnight, and if the concrete underneath has gone darker, moisture is trapped in it.
Two other concrete finishes cause trouble. Rust-Oleum warns that smooth, dense concrete and concrete with a curing compound will stop its coating sticking; if a few drops of water bead up rather than soak in, a sealer is present. Watco says power-floated concrete needs its own primer. Grinding the slab back gives the resin something to grip, as our page on how a resin floor is installed explains.
Check the screed first
Ceramic and quarry tiles
Yes, with the right preparation and primer. Altro makes an epoxy primer for exactly this, rated for fully and semi vitrified ceramic tiles, quarry tiles, polished marble and terrazzo, and Virtus Resins' primer also lists quarry and ceramic tiles. The steps from Altro's data sheet are what decide it:
- The glaze is diamond ground or lightly shot blasted until water drops soak straight into it.
- Hollow or loose tiles and crumbly grout come out and are reinstated first.
- Grout lines are filled level with primer, or they show through. Thin coatings copy the texture under them.
- The floor still needs a working damp proof membrane and moisture at 75% RH or below.
Altro puts it plainly: any failure of the base will always reflect through to the resin on top. Tap your tiles before you decide. If a lot of them sound hollow, lifting them may be less work than fixing them.
Laminate, vinyl and carpet
No. None of the resin makers whose data sheets we read lists laminate, vinyl or carpet as a base, and Altro asks for a substrate that is sound and stable. They come up, along with any underlay and adhesive, and the resin goes onto the floor underneath.
Timber floorboards and plywood
Possible, but only with a system made for it. Polycote's fast-cure coating lists wood as a base, and Watco's coating covers wood that is sound, clean and dry. Polycote's prep is to clean the timber, strip any old coatings and wax, and sand along the grain if needed. A timber floor is a different base to a concrete slab, so the product has to be one its maker rates for wood: not every resin that goes on a garage slab will go on floorboards. That is a question for the data sheet of the exact product, before you buy it.
Old floor paint
This is where makers genuinely split. Thin coatings will go over paint that is still well stuck: Watco says lightly abrade to remove any weak or loose paint and check the rest is well bonded, and Rust-Oleum's epoxy can go over old coatings that still adhere. Altro's primer for a resin topping takes the opposite line and wants all residues of old paint removed. The rule of thumb is that the heavier the system, the more it wants bare concrete. Peeling paint never stays: our comparison of a resin floor vs floor paint explains why it lets go.
An old epoxy floor
Yes, if the old epoxy is still bonded to the slab. Resin sticks well to resin once the surface has a key: Polycote and Altro both say to abrade a cured coat before the next one goes on, and Polycote's coating lists existing resin coatings as a base. Where the old floor is lifting or blistering, the loose areas come off first, because the new coat can only be as stuck as the old one. Our page on recoating an epoxy floor goes through it step by step, and epoxy floor problems covers what causes the lifting in the first place.
Tiles, paint or old epoxy on your floor?
Tell us what the floor is now and what the room is used for. We will check whether it can be coated where it is or needs taking back to the slab, and put that in a fixed written quote.
So what should you put over concrete?
If you have a sound concrete slab and want a hard, seamless finish, resin goes straight on it once it has been ground and dried. Published UK cost ranges put a thin resin coating at £30-£60 per m², the budget end (checked 2026-11-05), and our resin flooring cost page has the thicker systems. For a garage, our pick of the best resin floor for a garage and the comparisons with garage floor tiles and a concrete sealer cover the alternatives. If you want to coat it yourself, start with how to epoxy a garage floor.
About this page
Who wrote this
The Obsidian Resin team. We lay resin-bound driveways and resin floors anywhere in Great Britain, and every job starts with the same question this page answers: what is down now, and can it take resin.
Where the facts come from
UK system makers' own installation guides and data sheets: DALTEX (Derbyshire Specialist Aggregates), SureSet, Ronacrete and Natratex for driveways; Altro, KDR, Virtus Resins, Polycote, Watco and Rust-Oleum for floors. Where they disagree, as on how long new tarmac or concrete needs, we have said so rather than picking one.
Our honest position
We would rather you knew your base before anyone quotes, because a new base is the biggest cost difference on most jobs. If your drive or floor needs one, we will say so. If it does not, we will not sell you one.
Frequently asked questions
- Can you pour resin over gravel?
- Not over a loose gravel drive. UK makers say resin surfacing cannot usually go on a granular base, so the gravel is dug out and a proper base built. Compacted stone can take resin bound on a foot path only, laid at least 30 mm thick.
- Can resin be laid over block paving?
- No. DALTEX and Natratex both say block paving is not a suitable base: the joints between the blocks move and lead to cracks in the resin. The blocks are lifted and a tarmac or concrete base laid.
- Does resin bond to concrete?
- Yes, once it is clean, sound and primed. Makers call concrete harder to bond to, so they prime it and some add a crack reduction membrane. Expansion joints are carried up through the resin rather than covered.
- What goes under a resin driveway?
- On a new build, from the bottom up: a compacted Type 3 stone sub-base, a binder course of open graded asphalt, then the resin. Ronacrete suggests 200 mm of Type 3 and 60 mm of asphalt for a driveway, with at least 15 mm of resin on top.
- How long after laying new concrete can you put resin on it?
- It depends on the system. For a driveway, SureSet allows 7 days and DALTEX ideally 28. For a floor, data sheets ask for at least 28 days or 4 weeks, one says eight, and the slab must also be dry, at or below 75% RH.
- Can you put epoxy flooring over existing tile?
- Yes, if the tiles are sound. The glaze is ground or blasted off, hollow tiles replaced, grout lines filled level, and a primer made for tiles goes down first. Loose tiles will always show through.
- Can you put resin over laminate?
- No. Laminate, vinyl and carpet come up, and the resin goes on the floor underneath.
- Can you put resin over an old resin driveway?
- Only if the old surface is sound. A failed resin drive is usually planed off down to the base, and if that base is still in good condition the new resin goes straight back over it.
- What is the cheapest flooring to put over concrete?
- Among resin finishes, a thin coating is the budget end, at £30-£60 per m² in published UK cost ranges. It still needs the concrete cleaned, ground and dry, or it will not last.