The hard-wearing speckled floor that hides everything.
Decorative epoxy flake resin floors: coloured flakes broadcast into a wet resin coat and locked under a clear seal, about 1.5mm to 3mm thick in all. A speckled finish that hides dust and marks, in dozens of colour blends, for garages, workshops, gyms and changing rooms.
What you get
Hides the wear
The speckle disguises dust, tyre marks and small scuffs between cleans far better than one flat colour.
Sealed clear on top
One or two clear seal coats, gloss or matt, so the flake sits under the wearing surface rather than on it.
Grip where it gets wet
Flake on its own is a look, not a grip. Where the floor gets wet we add beads or aggregate to the seal.
Your blend, your density
Fine 1mm fleck or bold chips up to about 6mm, scattered lightly or broadcast until no base colour shows.
How it works
Tell us the details
Tell us the room, what it is used for and whether it gets wet, and the flake look you have in mind.
Quote in writing
A written quote, one fixed price covering everything, no surprises later.
New floor laid
Grind and prime, roll the coloured coat, broadcast the flake into it wet, then sweep, sand and seal.
Want a firm number? Send the size and your postcode and we come back with one written figure, not a range.
What a flake floor is, layer by layer
A flake floor is four layers. A primer goes into the ground-back concrete, then a coloured resin coat, then the flakes are thrown into that coat while it is still wet, then one or two clear seal coats lock them in. The UK systems we spec from run about 1.5mm thick for a light build up to about 2 to 3mm for a full flaked floor with a filled body coat.
Timing is the part people underestimate. Flake only sticks to wet resin, so one person rolls the coat and a second follows straight behind in spiked shoes, broadcasting within minutes. Once it has cured overnight, the loose flake is swept and vacuumed off, the proud edges are lightly sanded, and the clear coat goes on. Skip the sanding and the seal sits on sharp edges that catch dirt and feel rough underfoot.
Because the clear coat finds its own level, the slab has to be flat: a dip in the floor becomes a puddle of seal. That is one more reason the grind and repair come first, as our guide to how a resin floor is installed explains.
Full broadcast or a light scatter
There are two ways to lay flake, and they look nothing alike. A full broadcast buries the wet resin completely: the flake goes on in excess until no base colour shows, roughly 0.5 to 1.0kg of flake per square metre on the data sheets. A scatter is a light sprinkle of about 0.1kg per square metre, so the base colour reads through with flecks across it.
A full broadcast is the dense granite look and hides the most, and it uses five to ten times the flake, so it costs more in materials. A scatter suits a solid colour floor that wants a little life in it. Either way, flake size changes the effect: 1mm reads as a fine speckle, 3mm to 6mm as bold chips. Our guide to resin floor colours helps you pick a blend before we quote.
Is a flake floor slippery? Dry, no. Wet, it can be
The HSE rates floors by pendulum test value (PTV): 36 and above is low slip potential, 25 to 35 moderate, 24 and below high. One UK flake system publishes a PTV of 67 dry, but 17 wet, and 27 once polymer beads go into the seal. A full flaked epoxy from another maker is rated R9, and the HSE says R9 floors will be slippery when wet or greasy.
So the rule is simple. In a dry garage or hallway, a sealed flake floor is fine as it is. Anywhere water, sweat or oil lands, such as a wash bay, a home gym or a changing room, we put beads or a fine anti-slip aggregate into the seal, and the wet figure is the one to ask for.
The clear seal, and why it matters in a garage
The seal is the wearing surface, so it decides how the floor ages. Over flake we use epoxy, water-based polyurethane or polyaspartic clear coats, in gloss or matt. One UK maker states plainly that no resin system is totally colour fast and light colours show yellowing most, so where sunlight reaches the floor a UV-resistant polyurethane second coat is the safer choice. Our guide to whether epoxy yellows covers why.
Tyres are the other enemy. Plasticisers in rubber can migrate into a young coating and stain it for good, and hot tyres pull at a soft surface. Data sheets put full traffic at about 48 hours at 20°C and full chemical cure at about 7 days, so on a garage floor keep the car off for the week if you can, and let tyres cool before parking for the first few days.
Where flake suits, and where it does not
Flake is our usual pick for a working garage or workshop, a utility room, a home gym and a changing room, anywhere the floor gets used hard and you would rather not see every mark. If you want the showpiece look instead, compare it with our metallic floors, and our guide to the best resin floor for a garage sets out when to choose each.
Three honest limits. Epoxy flake systems are made for indoor use; outdoors you want a different system, covered on our outdoor resin flooring page. Joints and cracks in the slab still show through, so movement joints are carried up through the floor. And a patch laid years later comes from a different batch, so it will not be an exact match, though a busy flake hides a repair far better than a plain colour.
Flake floor specs at a glance
Figures from UK flake system data sheets. Cure times are at 20°C; at 10°C allow roughly double.
| What you want to know | Typical figure | What it means for you |
|---|---|---|
| Total thickness | About 1.5mm to 3mm | A coating system, not a screed. It goes over sound, flat concrete |
| Flake size | 1mm fleck to about 6mm chips | Smaller reads as speckle, larger as bold granite-style chips |
| Flake used, full broadcast | 0.5 to 1.0kg per m² | No base colour shows. Hides the most, costs more in flake |
| Flake used, light scatter | About 0.1kg per m² | The base colour reads through with flecks across it |
| Slip, smooth seal | PTV 67 dry, 17 wet (one system) | Fine dry. Needs beads or aggregate in the seal where it gets wet |
| Foot traffic | About 12 to 30 hours | Walk on it the next day in most cases |
| Full traffic | About 48 hours | Car back on after two days at the earliest, a week is better |
| Full chemical cure | About 7 days | Hold off on oils, cleaners and hot tyres until then |
| Laying conditions | Air and slab about 10 to 30°C | A cold garage in winter needs heating, and electric heat only |
Where we work
Anywhere in Great Britain
We lay flake floors anywhere in Great Britain, in garages, utility rooms, gyms and workshops. Published UK rates for flake and quartz broadcast systems sit at £45-£95 per m²; that is the market, not our price, and we send one fixed price for your floor in writing.
Resin in your city: Bristol, Newcastle, Glasgow, Manchester, London, Birmingham, Leeds, Liverpool, Sheffield, Leicester, Nottingham, Coventry, Derby, Plymouth, Bradford.
Common questions
- Is a flake floor slippery?
- Dry, no: one UK flake system tests at a PTV of 67 dry, well into the HSE low slip band of 36 and above. Wet, a smooth sealed flake floor can drop to high slip potential, so for wet areas we add beads or a fine anti-slip aggregate to the seal.
- How thick is a flake floor?
- About 1.5mm to 3mm in total on UK systems: primer, a coloured resin coat with the flake broadcast into it, and one or two clear seal coats.
- What is the difference between full broadcast and scatter flake?
- Full broadcast covers the wet resin until no base colour shows, using roughly 0.5 to 1.0kg of flake per m². A scatter uses about 0.1kg per m², so the base colour shows between the flecks. Full broadcast hides more and costs more in flake.
- How long before I can park on a flake floor?
- UK data sheets put full traffic at about 48 hours at 20°C and full chemical cure at about 7 days. Colder rooms take longer. Leaving the car off for the full week protects the seal from hot tyres.
- Can I match a colour scheme?
- Yes. Flake comes in dozens of colour blends and sizes, and we choose the base colour to sit under it. We lay out samples before we start, because the blend is locked in once it cures.
- What are the downsides of a flake floor?
- The textured versions hold a little more dirt than a smooth gloss and want the odd extra mop. A smooth seal is slippery when wet unless grip is added. And a repair years later comes from a new batch, so it will not match exactly.
- Can a flake floor go outside?
- Not an epoxy flake floor: the systems are made for indoor use and epoxy changes colour in sunlight. For a balcony, step or path, see our outdoor resin flooring page.
Get your quote.
Tell us about the space and we will come back with a written quote for the whole job.