Clean, seamless, one colour wall to wall.

Solid colour epoxy floor coating in gloss or satin, in the colour of your choice: either two rolled coats a fraction of a millimetre thick, or a poured self-smoothing floor at 2mm to 3mm. Seamless, hard-wearing and easy to keep looking sharp.

What you get

One clean colour

A single tone across the whole floor, from a standard range or a RAL shade, laid from one batch so it matches end to end.

Rolled or poured

A high-build rolled coating at about 0.3 to 1mm, or a self-smoothing pour at 2 to 3mm. We pick by slab and use.

Gloss or satin

High gloss for a bright, reflective room; a matt or satin polyurethane seal to tone down glare.

Grip without changing colour

Fine silica, quartz or glass beads go into the topcoat where the floor gets wet.

How it works

01

Tell us the details

Tell us the colour you are set on, the room, and whether it gets wet or sun.

02

Quote in writing

A single fixed price for the job in writing, sent over.

03

New floor laid

Grind, repair and prime, then roll or pour the colour, topcoat and cure.

Want a firm number? Send the size and your postcode and we come back with one written figure, not a range.

Rolled coating or poured self-smoothing: the two ways to get one colour

A solid colour floor is either rolled or poured, and the Resin Flooring Association (FeRFA) puts them in different classes. A floor coating is 150 to 300 microns, a high-build coating 300 to 1,000 microns, and a flow-applied floor, the self-smoothing or self-levelling kind, 2mm to 3mm. On the data sheets, a trade water-based epoxy goes on at 60 to 100 microns a coat and needs at least two coats; a high-build epoxy reaches about 400 microns from two; a self-smoothing epoxy uses about 3.6kg per square metre at 2mm.

Thickness changes what the floor forgives. A thin rolled coating mirrors every ripple and patch in the concrete, so the slab has to be good to start with. A poured floor flows flat over minor dips and gives the deeper, glassier solid colour people picture, but it needs a slab within a set flatness tolerance or a scratch coat first. Our guide to self-levelling epoxy goes deeper on the pour.

Choosing the colour, and keeping it

Makers sell solid colours from fixed ranges: one UK self-smoothing epoxy lists nine RAL shades, four of them greys, plus a red, a blue, a green, a white and a black; another trade coating has twelve standard colours with RAL or British Standard colours to order. Every sheet asks for one production batch per area, because two batches of the same colour can differ slightly side by side. That is why we order the whole floor at once.

No resin is totally colour fast. Sunlight and heat shift epoxy towards yellow over time, most visibly in light colours, blues and greys; it is cosmetic and does not weaken the floor. Where a window or open door throws sun across the floor, an aliphatic polyurethane or polyaspartic topcoat holds the colour truer. Our guide to whether epoxy yellows explains why, and choosing resin floor colours covers which shades hide dust and tyre marks.

Gloss, satin, and grip on a smooth floor

Most solid colour epoxies cure to a gloss, and high gloss shows fine scratches with use. A matt polyurethane seal over the colour can read below 10 gloss units, which takes the glare off and suits a living space or a bright showroom under strong lighting.

Smooth resin grips well dry: UK data sheets for smooth coatings publish dry pendulum values above 40, and the HSE counts 36 and over as low slip potential. None publishes a wet figure for a smooth finish, and manufacturers say plainly that textured systems are the answer for wet floors. One maker's figures show what grit does: 0.3 to 0.6mm silica in the topcoat gives a PTV of at least 40 wet and dry, and 0.7 to 1.2mm at least 55. For a garage washed down or a utility room, we add the fine grade; for a ramp, the coarse one. Our anti-slip page covers the grades.

When solid colour is the right floor, and when it is not

Solid colour suits a tidy garage, a showroom, a plant room, a light commercial unit, or any space where you want the floor to sit quietly and just work. It is the simplest finish to lay and, on the market rates below, usually the cheapest resin floor.

It is not the forgiving choice. A dark gloss shows every footprint and speck of dust, and a thin coat over a rough slab shows the slab. If you want marks hidden, a flake floor does that far better; if you want depth and movement, look at metallic. Weighing resin against bare concrete? See resin flooring versus polished concrete.

Solid colour systems at a glance

Figures from FeRFA and UK manufacturers' data sheets. Cure times are at 20°C; a cold room at 10°C roughly doubles or triples them.

SystemThicknessWalk on itFull cureSuits
Rolled epoxy coating (two coats)0.15 to 0.3mmAbout 16 hoursAbout 7 daysSound, flat slabs; stores, plant rooms, budget garages
High-build rolled coating0.3 to 1mmAbout 16 hours to light trafficAbout 7 days to full chemical cureGarages, workshops, light commercial
Poured self-smoothing epoxy2 to 3mmAbout 24 hoursAbout 7 daysShowrooms, kitchens, a deep glassy finish
Matt PU seal over the colourA thin topcoatPer the system underneathPer the system underneathGlare-free living spaces, sunny rooms

Where we work

Anywhere in Great Britain

We lay solid colour floors anywhere in Great Britain, from a single garage to a full commercial unit. Published UK market rates are £30-£60 per m² for a rolled coating and £40-£80 per m² for a poured self-levelling floor. Those are what the market charges, not our price; we send one fixed price for your floor in writing.

Resin in your city: Bristol, Newcastle, Glasgow, Manchester, London, Birmingham, Leeds, Liverpool, Sheffield, Leicester, Nottingham, Coventry, Derby, Plymouth, Bradford.

Common questions

How thick is a solid colour epoxy floor?
A rolled coating is 150 to 300 microns, or up to 1mm as a high-build coating. A poured self-smoothing floor is 2mm to 3mm. Those are FeRFA's bands, and they decide how much of the slab shows through.
Can I have any colour?
Close to it. Makers sell standard ranges, often by RAL number, and some mix RAL or British Standard colours to order. We order the whole floor from one batch so the colour matches across the room.
Gloss or satin, which is better?
Gloss looks sharper and reflects light, but shows fine scratches with use. A matt or satin polyurethane seal cuts glare and suits living spaces. We talk through which suits your room.
Is a smooth resin floor slippery?
Dry, no: smooth coatings publish dry pendulum values above 40, in the HSE low slip band. Wet, it can be, so we add fine silica or glass beads to the topcoat where water lands, without changing the colour.
Will it fade or yellow?
Indoors out of the sun it holds its colour well. Epoxy shifts towards yellow under sunlight, most in light colours and blues, so for sunny rooms we use a UV-stable polyurethane or polyaspartic topcoat.
What is the difference between epoxy floor paint and a resin floor coating?
A tin of floor paint is a thin surface coat that sits on top of the concrete, so it lifts under tyres and traffic. A laid resin floor is bonded to the ground-back slab as one seamless, hard-wearing surface, from a fraction of a millimetre to 3mm thick.

Get your quote.

Tell us about the space and we will come back with a written quote for the whole job.