An epoxy floor that has gone dull, scuffed or tired is usually still a perfectly good base. You do not need to grind it all off and start again. But you cannot just roll a fresh coat over the top either. Cured epoxy is hard and glassy, and a new coat poured straight onto it has very little to hold on to. Here is how to tell whether yours can be recoated, how to prep it so the new coat stays put, and when stripping it back is the better job.
Recoat or strip back: the quick check
| What you see | What it usually means | What to do |
|---|---|---|
| Dull, scuffed, light scratches | Wear in the top surface only | Degrease, sand until matt, recoat or topcoat |
| Yellowed but sound | UV ageing of the epoxy surface | Sand and add a UV-stable topcoat |
| Small chips or a few lifted patches | Local damage or local bad prep | Cut back to sound edges, prep the bare concrete, patch, then recoat |
| Coat lifts off under tape across the floor | The old coat never bonded properly | Strip back to concrete |
| Blisters that leak liquid when broken | Moisture pushing up from the slab | Strip back and deal with the damp first |
| Old coat softens under a solvent rub | A single-pack paint, not a two-pack coating | Strip it, or stay with a single-pack paint |
The rule behind every row: a new coat bonds to the old one. It cannot glue the old one back down to the concrete. If the old coat is holding on well, recoating works. If it is not, anything you put on top fails with it.
Will new epoxy stick to old epoxy?
It will, but not the way two coats stick together on a new floor. While epoxy is still curing, its surface can react with the next coat and form a chemical bond between the two. Manufacturers call the time this works the recoat or over-coating window, and every UK data sheet gives one. Once it has passed, the old surface has fully hardened and that chemical bond is no longer on offer. From then on the only bond is mechanical: the new coat locks into scratches sanded into the old one.
These are the windows from UK manufacturers' own data sheets, all at 20°C. They take longer in a cold garage and shorter in a warm one.
| Product type | Next coat after | Must go on within | If you miss it |
|---|---|---|---|
| Clear epoxy (Virtus Strongcoat) | 16 hours | 36 hours | Abrade the first coat |
| 100% solids epoxy (Polycote Flortex Professional) | About 12 hours | 36 hours | Abrade the first coat |
| Polyurethane topcoat (Virtus Chemdur Clear) | 16 hours | 36 hours | Abrade thoroughly, then recoat |
| Polyaspartic coating (Polycote Flortex Fastset) | 2 to 3 hours | 8 hours | Abrade the first coat |
| Polyaspartic topcoat (Virtus Flowdur PAS) | 90 minutes | 12 hours | Abrade the coating |
Look at the right-hand column. Every sheet that names a window gives the same instruction once it has gone: abrade. And the longest window on the list is a day and a half. A floor laid last year, or ten years ago, is outside every one of them, so recoating an old epoxy floor is always an abrasion job first and a painting job second. That is why "can I just pour epoxy over dried epoxy?" gets the answer it does. You can pour it, but on a glossy surface it has nothing to grip.
Worth knowing on a new floor too
How to test the old coat before you recoat
Twenty minutes of testing tells you whether the job is a weekend recoat or a strip-back. Do these three checks in the worst spots, not the best: inside the door, under where the tyres sit, along any wall that might be damp.
1. Look for the warning signs
Walk the floor in good light and look for peeling, bubbling, chemical damage and areas that have lost their gloss far faster than the rest. Press any bubble. A soft or hollow-sounding patch is a coat that has let go of the concrete underneath, and it has to come off before anything else happens.
2. The knife and tape check
With a sharp utility knife, score a small cross through the coating right down to the concrete. Press a strip of strong tape, such as duct tape, firmly over the cross, rub it down, then rip it off fast. Clean cut edges with the coat still stuck to the floor mean it is bonded well. Flakes of coating on the tape, or the coat lifting away from the cut, mean it is not, and anything you lay on top will come away with it. If one area fails, test a few more to see if the problem is one patch or the whole floor.
3. The solvent rub: is it really epoxy?
A floor that looks like epoxy may be a single-pack floor paint, and the difference matters. One UK floor paint maker gives a simple test: soak a rag in standard thinners or xylene and rub a small patch hard for 60 seconds. If the coating softens, dissolves or comes off on the rag, it is almost certainly a single-pack water-based paint, and a two-pack epoxy should not go over it. If it shrugs the solvent off, it is a chemically cured coating, epoxy or polyurethane, and a similar two-pack system can go on top. Do this on a small patch away from the door, wearing gloves, with the garage door open.
Then, if you are still unsure after all three, do what the manufacturers themselves advise and lay a trial area first. Prep a square metre exactly as you would the whole floor, coat it, let it cure fully and tape-test that. It costs a few days and saves a whole floor.
How to prep an epoxy floor for a new coat
The prep for a recoat is lighter than for bare concrete, but every step is there for a reason. Skip one and the new coat is the one that peels.
- Clear and repair first. Scrape off anything loose or lifting, cutting back to edges that are firmly stuck down. Rust-Oleum's instructions for previously painted floors say the same: remove loose paint by sanding and scraping before anything else.
- Degrease before you sand, not after. Scrub the whole floor with a heavy-duty degreaser and rinse it well. Sanding a dirty floor drives oil and grease down into the fresh scratches, which is exactly where the new coat needs to grip. Let it dry completely.
- Sand until there is no shine left. On a garage floor that means a floor buffer with a 120-grit sanding screen, or an orbital sander on a small area. You are taking the gloss off, not the coating. When you are done the floor should look dull, matt and dusty white all over. Any spot that still reflects light gets sanded again, including edges and corners, because a missed glossy patch is where a new coat lets go first.
- Vacuum, then solvent wipe. Vacuum every bit of dust, then go over the floor with a mop dampened with the thinner the new product's data sheet names. Wipe your fingers across it when it is dry: if they come up dusty, clean it again.
- Prime only the bare patches. A sound old coat acts as the sealer, so it does not usually need a primer. Any areas you cut back to concrete are different: they need the same prep as a new floor, laitance off, slab dry to below 75% relative humidity, and primer, before the recoat goes over the top.
One thing that catches people out: a fresh clear coat over a smooth resin floor can fish-eye, pulling back into small craters as it is rolled out. Two UK makers give the same cure in their data sheets, a light abrade followed by a solvent wipe, which is one more reason the sanding is not optional. There is more on why coats fail in our page on common epoxy floor problems.
Tape test came back patchy?
Tell us what your floor is doing and roughly how big it is. We will say whether it can be recoated or needs grinding back, and put either job in a written quote.
When to strip it back instead
Recoating is only ever as good as the coat underneath. These are the signs that the old floor has to come off, back to bare concrete:
- The coat fails the tape test in several places, or peels away in sheets.
- The solvent rub shows a single-pack paint and you want a two-pack epoxy on top.
- There are layers of different old coatings, and nobody knows what any of them are.
- The concrete under it was never ground, or was sealed with a curing compound, which is why it let go.
- There are blisters with liquid in them.
Blisters full of liquid are a damp problem
FeRFA, the UK resin flooring trade association, describes a specific kind of failure called osmotic blistering. The blisters run from a few millimetres to about 100 mm across and up to about 15 mm high, and when you break one, liquid comes out under real pressure. They show up between three months and two years after the floor was laid, and they are rare, well under 1% of floors. But if your floor has them, a new coat on top is pointless. The moisture is coming up through the slab, and it will push the new coat off the same way. The floor needs stripping, the damp dealing with, and a proper moisture-tolerant build. Our page on resin over cracked or damp concrete covers what that involves.
Stripping a floor means grinding it off with a diamond grinder and dust extraction, which is the same machine work as preparing a new slab. Published UK rates for that mechanical prep run at £8-£20 per m² on a domestic floor, and a full self-levelling epoxy floor on top sits at £40-£80 per m², according to published UK cost figures checked 2026-11-05. Nobody publishes a separate rate for a recoat or a topcoat refresh, so the honest way to compare the two jobs is two quotes for your floor. Our resin flooring cost breakdown has the rest of the published figures.
Recoating over painted concrete
A garage floor that was painted rather than coated is a different starting point, and the solvent rub above is the test that sorts it. Single-pack floor paints, the tins most DIY garage floors start with, are softer and weaker than a two-pack epoxy. A two-pack coat should not go over them, and mismatched solvents can make old paint bubble, wrinkle and lift. So the choice is simple: either stay with the same kind of single-pack paint, or take the paint off and lay a proper system on the concrete.
If the old coating turns out to be a two-pack product and is well bonded, it can be recoated like any other. Some UK products are made for exactly this. Rust-Oleum's DIY water-based epoxy says it can go over old coatings that are still adhering well, after loose paint is sanded and scraped off and the floor degreased. Watco's polyaspartic topcoat is sold as protection for previously painted floors, with the instruction to lightly abrade, remove weak paint and check what is left is well bonded. Our comparison of resin flooring and garage floor paint explains why a painted floor keeps needing doing, and concrete sealer versus epoxy covers the other common coating that epoxy will not bond to.
Recoating over a flake floor
A flake floor is a base coat, a broadcast of coloured flakes, and a clear topcoat locking them in. When it wears, it is usually that clear topcoat going dull and scratched while the flakes underneath are fine. That makes it one of the easiest floors to refresh: clean, sand the topcoat until matt, vacuum, and lay a new clear coat.
The detail that matters is the flakes themselves. Any that have worked loose need sweeping and vacuuming off, and flakes standing proud of the surface get a light sanding to knock them down. Virtus's polyaspartic topcoat data sheet gives its coverage for "thoroughly de-nibbed and sanded flake systems", which tells you what the surface should be before it goes on. Skip that and every raised flake shows through the new coat as a bump. If you want to change the colour rather than just bring back the shine, a new flake broadcast over a sanded old floor is also possible, with a new base coat to carry it.
A topcoat refresh: polyurethane or polyaspartic
For a floor that is sound but tired, often all it needs is a new clear topcoat rather than more epoxy. A topcoat goes on thin, around 60 to 75 microns a coat for a polyurethane and about 200 for a polyaspartic, so it puts back the shine and the scratch resistance without building the floor up. The UK topcoats on this page are UV stable, which is the real reason to choose one over another epoxy coat: epoxy yellows in sunlight and these do not. That makes a topcoat refresh the usual fix for a floor that has yellowed in the sun.
Polyaspartic is the quick one. Sika sells its polyaspartic topcoat in the UK as a "fast-curing maintenance coating", prepared over an existing coating by mechanical grinding and vacuuming. The catch is the window in the table above: it is short, so two coats have to be planned for the same day. Our full comparison of epoxy and polyaspartic covers the cure times and the cold-weather side. One honest limit from a UK data sheet: a clear polyaspartic topcoat may not stop the coating underneath discolouring in strong UV, so on a very sunny floor in a pale colour, a refresh slows yellowing rather than undoing it.
Sika's polyaspartic topcoat lists an isocyanate as its hardener, and its sheet says the product "may only be used by experienced professionals". If you are tempted to do it yourself, read our page on whether epoxy is toxic first, because the protection you need goes up a step from a water-based epoxy.
Doing it yourself or having it done
A sound, scuffed garage floor is a fair DIY job. Allow time for the floor to dry fully after degreasing, and wait for a warm spell for the coat to cure: most epoxies want the air and the slab at 10 to 15°C or more. Hire a floor buffer with sanding screens, test first, and follow the new product's data sheet to the letter. Our walk-through of how to epoxy a garage floor covers the coating side step by step, and epoxy not curing covers what to do if a coat stays tacky.
Where it stops being a DIY job is anything that needs grinding: a floor that fails the tape test, large areas cut back to concrete, or a strip-back. That needs a planetary grinder with proper dust extraction and someone who has used one. It is how our own floors start too: diamond grinding, the cracks repaired, then the dust taken right out. You can see how the rest goes in how a resin floor is installed, and our garage floor resin page shows the builds we lay.
Want the old floor ground back properly?
Whether it needs a strip-back, a patch-and-recoat or just a new topcoat, tell us about the space and we will quote the job your floor actually needs.
Keeping the new coat looking good
Once it is down, a recoated floor is looked after the same way as a new one: sweep the grit off, mop with a pH-neutral cleaner, and wipe spills before they sit. The routine is in our page on how to clean and maintain a resin floor, along with what to keep off it. Keep the grit down and the next refresh is a long way off.
About this page
Who wrote this
This page is from the Obsidian Resin team. Recoats and new floors are both work we take on, in workshops and garages across Great Britain.
Where the figures come from
The recoat windows are from UK manufacturers' technical data sheets for Virtus Resins, Polycote, Sika, Rust-Oleum UK and Watco, read in November 2026. The blistering detail is from FeRFA, the Resin Flooring Association. Prices are published UK market ranges from cost websites, not our own rates.
Our honest position
We would rather recoat a sound floor than grind off a good one, and we would rather grind off a failing one than sell you a coat that will not last. Testing the old floor first is how you tell which one you have, and you can do that yourself before you ring anyone.
Frequently asked questions
- Will new epoxy stick to old epoxy?
- Yes, if the old coat is still firmly bonded to the concrete and you sand the gloss off it first. An old floor is past every recoat window, so the new coat cannot form a chemical bond with it and relies on the scratches sanding leaves. On glossy, unsanded epoxy it has very little to grip.
- Can I pour epoxy over dried epoxy?
- Only after sanding it. UK data sheets give a recoat window of between 8 and 36 hours depending on the product, and every one says to abrade the old coat once that window has passed. Degrease, sand until the floor is matt all over, vacuum, solvent wipe, then pour.
- Can you recoat an epoxy garage floor?
- Yes. A dull or scuffed garage floor that passes a knife-and-tape test can be degreased, sanded with a 120-grit screen and recoated, or given a new clear topcoat. Peeling patches are cut back and prepped first. A floor that lifts under tape in several places needs stripping back to concrete.
- How do you repaint an epoxy floor?
- Test it, repair it, degrease it, sand it until there is no shine left, vacuum, wipe with the thinner the new product names, then coat. Prime only areas cut back to bare concrete. If the old floor is single-pack paint rather than epoxy, a two-pack epoxy should not go over it.
- How do I know if my floor is epoxy or paint?
- Rub a small patch hard for 60 seconds with a rag soaked in thinners or xylene. If it softens or comes off, it is a single-pack paint. If it is unaffected, it is a chemically cured coating such as epoxy or polyurethane, and a two-pack system can go on top.
- Can I put a polyurethane or polyaspartic topcoat over old epoxy?
- Yes, over a sound floor that has been sanded or ground and cleaned. Both are UV stable, so it is the usual fix for a yellowed floor. Polyaspartic cures fastest but has the shortest recoat window. There is more in our epoxy versus polyaspartic comparison.
- Is it cheaper to recoat than to strip and relay?
- Usually, because the grinding is where most of the work is. Published UK cost figures put mechanical prep at £8-£20 per m² on a domestic floor, but nobody publishes a rate for a recoat, so get both jobs quoted for your floor.