"Is epoxy toxic?" is the wrong shape of question, because the answer changes over the life of the floor. Epoxy arrives as two liquids, a resin and a hardener. Mixed, they react and set into a solid. The hazards on the tin belong to those liquids, and they fade as the floor cures. So the useful questions are: what can the wet material do to you, how do you stop it, and when is the room safe to use again. This page answers each one from the HSE and from UK manufacturers' own safety data sheets.
Wet, curing and cured: the risks at each stage
| Mixed and wet | Curing (first week) | Fully cured | |
|---|---|---|---|
| Skin | Main hazard: irritant and skin sensitiser | Tacky or soft spots can still be uncured resin | A hard solid surface |
| Eyes | Irritant; some hardeners cause serious eye damage | Low once surface is dry | No liquid left |
| Breathing | Vapour, from almost none to a lot, by system | Smell fades as it cures | Only if ground or sanded (dust) |
| Fire | Solvent-based products are flammable | Keep ignition sources away until dry | n/a |
| Who is in the room | The people laying it, in PPE | Nobody else, and no food | Normal use |
"Fully cured" means what the data sheet says, and for most epoxies that is about seven days at 20°C. Remmers' sheet puts it plainly: "completely cured after 7 days. Correspondingly longer at lower temperatures." A cold garage takes longer. The sections below explain each row.
Why epoxy is a skin problem: sensitisation
The main health risk from epoxy is to your skin, and it comes in two forms. The HSE's dermatitis leaflet, INDG233, describes both. Irritant contact dermatitis "is caused by things that dry out and damage the skin, eg detergents, solvents, oils". Allergic contact dermatitis "occurs when a person develops an allergy to something that comes into contact with their skin", and the HSE lists "Epoxy resins" among its common causes, next to cement.
The allergy is the one to respect, for three reasons the HSE gives:
- It can be delayed. "The allergic reaction can appear over hours or days, or even months." Getting away with it on one job tells you nothing about the next.
- It is likely to be permanent. "Once someone is 'sensitised', it is likely to be permanent," and after that "any skin contact with that substance will cause allergic contact dermatitis." That is how people end up unable to work with epoxy at all.
- It builds up. "Dry, red and itchy skin is usually the first sign. Flaking, blistering, crusting, cracking, swelling and pain can follow," and "the effects can be cumulative."
You will see this on every tin. UK epoxy floor safety data sheets from Johnstones (PPG), Floorsaver, Permagard and others all carry H317, "May cause an allergic skin reaction", and many add EUH205: "Contains epoxy constituents. May produce an allergic reaction."
The hardener has hazards of its own
The HSE names "epoxy resins and hardeners" as skin hazards in its construction skin FAQ, and the hardener tin is often the worse of the two. Permagard's PermaCOAT hardener carries the signal word "Danger" and H318, "Causes serious eye damage", from its amine content, while the matching base is classed as an eye irritant. That is why goggles matter most at the moment you open and pour the hardener.
Fumes and VOCs: it depends which epoxy
Epoxy floor products fall into three families, and what you breathe depends heavily on which one is in the tin. VOC (volatile organic compound) content, in grams per litre, is printed on the data sheet, so you can check before you buy.
| Type | Example UK product | Stated VOC | What the sheet says about air |
|---|---|---|---|
| Solvent-based | Johnstones 2 Pack Solvent Based Epoxy Floor Paint | Up to 500 g/l | Flammable; respirator when ventilation is inadequate |
| Water-based (DIY) | Rust-Oleum EpoxyShield 5300 MAXX | 53 g/l max | Avoid skin and eye contact |
| Solvent-free trade epoxy | KDR EpoCoat HB | Under 128 g/l | Safety equipment per the SDS |
| Epoxy floor base | Permagard Epoxy Floor Coating HB | 114 g/l | Sufficient ventilation; respirator not required |
Two things in that table surprise people. First, "solvent free" does not mean zero VOC: KDR's solvent-free epoxy still states under 128 g/l. Second, solvent-based floor epoxy is a different animal. The Johnstones base contains xylene, is classed "Flammable liquid and vapour", and its sheet warns that solvent vapour above the exposure limit can cause "headache, dizziness, fatigue, muscular weakness, drowsiness and, in extreme cases, loss of consciousness." That is the product type that earns epoxy its reputation for fumes.
Water-based epoxy is the low-smell end. Watco describes its water-based Epoxy Gloss Coat as a "low odour application", and the HSE's construction guidance suggests "using water based paints, glues or coatings in preference to solvent or epoxy based products" where the job allows. The trade-off is build: water-based floor paints go on thin, while a self-levelling epoxy or a heavy flake build needs a solids system. Our page on sealers versus epoxy covers where each one fits.
The hazard most people miss: dust from the prep
Every proper resin floor starts with grinding or shotblasting the concrete, and concrete contains silica. FeRFA, the Resin Flooring Association, puts it bluntly: "Silica dust is a serious occupational health hazard, that is often present when preparing substrates before the application of resin systems."
The HSE's construction dust sheet explains why a garage is a bad place for it: "High-energy tools like cut-off saws, grinders and grit blasters produce a lot of dust in a very short time," and "the more enclosed a space, the more the dust will build up." Its answer is on-tool extraction with "an H or M Class extraction unit" plus a mask. "The general level for construction dust is an APF of 20," meaning the wearer breathes one twentieth of the dust in the air, and "RPE is the last line of protection."
This matters to anyone weighing up a DIY floor. The resin is the part everyone worries about, but an hour with a hired grinder in a closed garage, with a household vacuum and a paper mask, can be the riskier afternoon. It is also why grinding is not a step to skip: an unground slab is the main reason floors lift, as our page on how a resin floor is installed explains.
Rather not grind silica dust in your own garage?
We diamond grind the slab, contain and vacuum the dust, and lay a 100% solids epoxy with no solvent in it. You keep out of the room while it cures. Tell us about the floor and we will quote it.
Gloves, masks and goggles: what the data sheets ask for
Gloves
The HSE's glove advice starts with a warning: "No glove material will protect against all substances and no gloves will protect against a specific substance forever." It asks for gloves to EN374-3, non-latex where possible, and notes that "manufacturers' data is for pure chemicals, not mixtures", which an epoxy is. What UK epoxy floor sheets name:
- Nitrile gloves: Permagard Epoxy Floor Coating HB and Remmers.
- "Nitrile rubber, butyl rubber, PVC, Viton": Johnstones solvent-based epoxy.
- Over 8 hours breakthrough for polyethylene (PE) and polyvinyl alcohol (PVA): Floorsaver epoxy resin.
Change gloves the moment they are splashed or torn, and keep sleeves down: Floorsaver asks for long sleeves and Remmers for a "long sleeved shirt or arm protectors". Forearms and wrists are where resin gets past the glove.
Eyes
At minimum, safety glasses with side shields to EN166 (PermaCOAT). For the solvent-based Johnstones product, "Chemical splash goggles and face shield."
Respirators: which filter, and when
Whether you need one depends on the product and the room, and the sheets disagree for good reason. Permagard's HB base says "Respiratory protection not required" with sufficient ventilation. Floorsaver says "Good general ventilation should be sufficient", but recommends "organic vapour (Type A) and particulate filter" where a mask is used. Johnstones' solvent-based product says to "Wear appropriate respirator when ventilation is inadequate."
If you wear one, the filter type is the detail that matters. In the HSE's respirator guidance, HSG53, a brown Type A filter is for "Organic gases and vapours" and a white P filter is for particles, and the two do not overlap: "Gas/vapour filters do not protect against particles" and "Particle filters do not protect against gas or vapour." A combined filter such as A2P3 does both, which suits a job that goes from grinding to rolling resin in the same day. Two more points from the HSE:
- Vapour filters fill up. "When breakthrough occurs, the RPE offers no protection." A capacity 1 filter should be changed at least every two days, and daily where it is protecting against a sensitiser, unless the maker says otherwise.
- A tight-fitting mask only works if it fits: face fit testing, and the wearer "needs to be clean shaven."
If you get it on your skin
Deal with it straight away. KDR's data sheet says spills on skin should be cleaned "by dry wiping of the affected area, and thorough washing with soap and water." Never reach for thinners or white spirit: the Johnstones sheet says "Do NOT use solvents or thinners" on skin, and solvents are an irritant in their own right.
Ventilation, and how long the smell lasts
Air movement does most of the work while the floor is laid and curing. Watco's application advice is "warm (minimum 15°C), dry conditions with good ventilation," and the solvent-based sheets add that vapour must be kept away from flames and sparks, which includes a gas boiler or a heater in the same space.
UK data sheets do not put a number of hours on the smell. What they give is the cure, and the smell fades as the floor cures: foot traffic after about 12 to 24 hours, full cure about seven days at 20°C, longer in the cold. Virtus Resins' sheet for its Strongcoat epoxy says to "Remove food products from the area during application and curing," which is a sensible rule for the whole week. In practice that means:
- Keep doors or windows open while the resin is laid, and through-draught where you can.
- Keep the internal door from a garage to the house shut.
- Move food, pet food and pet bedding out of the room before you start.
- Keep children and pets out until the full cure time on the data sheet has passed.
If you are planning around that week, our FAQ on how long a garage is out of action has the practical timings, and a polyaspartic floor is back in use much sooner.
Is a cured epoxy floor safe in a home with children and pets?
The hazard statements on a safety data sheet describe the product as supplied: the liquid resin and the liquid hardener. Once they have reacted and fully cured, the floor is a hard plastic, and some epoxy systems are made for places far fussier than a home. KDR lists "Food Processing" among the uses for its EpoCoat HB, and Flowcrete notes that resin floors with HACCP International certification have been "specifically tested" for the hygiene needed on "intensive, large-scale food production sites".
We have not found a UK body that issues a specific statement on cured floors and children or pets, so here is the practical position. The real risk in a "finished" floor is one that never fully cured. Virtus warns that "unmixed material will result in uncured" patches, and those soft or sticky spots are still reactive resin. A floor that is hard, even and tack-free after its full cure time is a different thing from a floor with a soft patch by the door. If you have a sticky area, keep people and pets off it and read our page on epoxy that is not curing.
The one-line rule
Is epoxy carcinogenic?
Not on the UK epoxy floor sheets we have read. Permagard's PermaCOAT base and hardener both state for carcinogenicity: "Based on available data, the classification criteria are not met." Floorsaver and Johnstones state "No known significant effects or critical hazards." The classified hazards are skin irritation, skin sensitisation and eye damage, plus flammability for solvent-based products. One caution: some filled coatings contain a lot of quartz. Permagard's HB base lists 30 to 50% quartz with a "prolonged or repeated exposure" warning, which is another reason to treat dust from grinding old coatings or concrete seriously.
The safer way to get an epoxy floor
The HSE's approach to skin hazards is avoid, protect, check, and it works for a floor too. In order of what helps most:
- Pick a lower-hazard product. Water-based or solvent-free over solvent-based. The HSE suggests substitution first, and solvent-free trade systems such as KDR's, or Virtus' Flowdur, which it describes as "100% solids. VOC free", remove the solvent vapour problem.
- Keep it off your skin by method. The HSE suggests long-stemmed rollers and using equipment rather than hands: "don't use your hands as tools." Mix in a bucket on the floor, not on your knee.
- Then the kit. Gloves, goggles and long sleeves always, and the right filter if you need a mask. The HSE is clear that "As a last resort, gloves and other protective equipment may be used."
- Check your skin. Dry, red, itchy hands after a resin job are the first sign. Stop and get them looked at before the next job, not after.
If you are doing it yourself, our page on how to epoxy a garage floor walks through the job, and resin versus floor paint sets out what a water-based paint will and will not do.
Want the floor without handling the resin?
We do the mixing, the pouring and the clean-up, in our own gloves and masks, and you come back to a floor that has cured. Tell us the size of the room for a written price.
About this page
Who wrote this
The Obsidian Resin team. We prep and lay resin floors for garages, workshops, kitchens and commercial units anywhere in Great Britain, using two-pack, 100% solids epoxy on slabs we diamond grind and vacuum twice.
Why we wrote it
"Is it safe?" comes up on almost every home enquiry, often from people with young children or a dog that sleeps in the garage. The answers online tend to be either alarming or breezy. This page states what the HSE and the manufacturers' own safety data sheets say, so you can judge it yourself.
Our honest position
We lay floors for a living, so we would rather you had one laid than did it yourself. People do lay their own epoxy, and this page gives them the same facts. Always read the safety data sheet for the exact product you buy; it overrides anything general, including this.
Frequently asked questions
- Is epoxy resin toxic to breathe?
- It depends on the product. Solvent-based floor epoxies give off flammable solvent vapour that can cause headaches and dizziness above exposure limits. Water-based and solvent-free epoxies give off far less: UK sheets state 53 g/l for a water-based DIY epoxy and under 128 g/l for a solvent-free trade epoxy, against up to 500 g/l for a solvent-based one. Ventilate whichever you use.
- Do I need to wear a respirator when using epoxy?
- Check the safety data sheet. Some UK sheets say respiratory protection is not required with good ventilation; solvent-based ones ask for a respirator when ventilation is inadequate. If you wear one, use a Type A (brown) organic vapour filter for resin, and add a P filter for dust, as A2P3, if you are grinding too.
- How long does epoxy give off fumes?
- The smell fades as the floor cures. Most epoxies take foot traffic after about 12 to 24 hours and fully cure in about seven days at 20°C, longer in the cold. Keep the room ventilated, and keep food, children and pets out until the full cure time on the data sheet has passed.
- Is resin toxic after it dries?
- Touch-dry is not cured. Once fully cured, about seven days for most epoxies, the floor is a hard solid plastic, and some systems are used in food production. A patch that stays soft or tacky has not cured and should be treated as wet resin.
- Is epoxy a carcinogen?
- The UK epoxy floor safety data sheets we have read do not classify it as one: PermaCOAT states the carcinogenicity criteria are not met, and Floorsaver and Johnstones state no known significant effects. The classified hazards are skin and eye irritation and skin sensitisation.
- What are the health risks of epoxy flooring?
- Mostly to skin. The HSE names epoxy resins as a common cause of allergic contact dermatitis, and once someone is sensitised it is likely to be permanent. Hardeners can also cause serious eye damage. On the prep side, grinding concrete makes silica dust, which FeRFA calls a serious occupational health hazard.
- Is an epoxy floor safe for children and pets?
- Keep them out while it is laid and until the full cure time has passed, and move pet food and bedding out first. After a full cure the floor is a hard plastic surface. We have not found a UK body statement specific to children or pets, so treat any soft or sticky spot as uncured.
- What is a safer alternative to solvent-based epoxy?
- A water-based or solvent-free epoxy. The HSE suggests swapping to lower-hazard products first, then keeping resin off your skin by method, with gloves and other PPE as the last resort. A solvent-free system laid by someone else keeps you away from the liquid altogether.