How to clean a resin driveway

Sweep, hose and the occasional careful jet wash keep a resin bound drive looking new. Here is how far to hold the lance, what each stain needs, and what to keep off it.

The short answer

Sweep it with a stiff broom and hose it down. When it needs more, a jet wash is fine: cold water, a fan nozzle, no more than 150 bar, the lance held at least 20 to 30 cm off the surface and kept moving side to side. Treat moss with a moss and algae killer, oil with neat washing-up liquid left for 10 minutes, and keep petrol and solvents off it. You do not need to seal a resin bound drive to keep it clean.

A resin bound driveway is stone held in clear resin with tiny gaps all the way through, which is why rain drains straight into it. That open texture is what you are cleaning. Dirt, leaves and moss sit on and in those gaps, so the job is to lift them out without blasting the stones loose or washing anything harsh down into the ground. Here is how to do it, stain by stain, using what the UK resin system makers tell their own customers.

What the makers say about jet washing (scan this first)

Yes, you can jet wash a resin driveway. Every maker's aftercare sheet we checked allows it. What they do not agree on is the detail, so here are the numbers side by side.

MakerPressureLance distanceNozzle and angleWater
Daltex (Derbyshire Aggregates)Up to 150 barAt least 200 mmFan jetCold only
Addagrip (Addabound)Up to 150 bar200 mmFan lanceCold
GCL (PermaBound)150 bar (2,175 psi) maximumNo closer than 200 mmFan jetCold only
VubaOnly as much as lifts the dirtAt least 300 mmFan jet, about 45 degrees, side to sideCold, 40°C maximum

If you do not know whose resin is on your drive, follow the strictest of each: no more than 150 bar, the lance 300 mm off, held at an angle, cold water. That keeps you inside every maker's rules. SureSet's own brochure puts the whole routine in one line: sweep and occasionally power wash.

The routine: sweep, hose, then jet wash

Most of the time a resin drive only needs a stiff broom and a hose. Daltex's aftercare sheet says to sweep it regularly, taking off leaves and debris so moss has nothing to grow in, then hose it with clean water. Vuba says the same, and adds that cleaning products should only come out when water and a brush are not enough. Keep wire brushes and abrasive pads off it.

Leaves matter more than people think. Wet leaves, twigs, seeds and conkers left lying release tannins that stain the stone brown. Addagrip and Daltex both warn about it. Clearing them in autumn is the single easiest thing you can do for the colour of your drive.

How to jet wash it without damage

  • Sweep first, so the jet only has to deal with what the broom left behind.
  • Set the machine low. 150 bar is the most any maker allows, and Vuba asks for only enough to shift the dirt.
  • Fit the fan or flat nozzle every maker asks for, so the water spreads instead of cutting.
  • Hold the lance at least 200 mm off the surface, 300 mm if you can, angled at about 45 degrees rather than straight down.
  • Keep it moving side to side. Parking the jet on one spot is how stones get knocked out.
  • Use cold water, and skip particularly cold days.

No maker sets a fixed timetable. They say clean it periodically, as often as it needs to keep its looks. A shaded drive under trees will want it far more often than an open one in full sun. When SureSet went back to clean a resin bound surface it had laid 15 years earlier, the team ran a rotary surface cleaner over it first, then rinsed with an ordinary household pressure washer, going over it in several directions.

New drive?

Full chemical resistance takes time to build. Daltex says to keep chemicals off the surface for the first 7 days after it is laid. Sweeping and plain water are fine; save the cleaners and stain removers until after that first week.

Stains, one by one

ProblemWhat the makers useWatch out for
Moss and algaeBrush off, then a proprietary moss and algae killer or fungicideMakers split on rinsing it off afterwards (see below)
Ingrained green algaeA strong bleach solution, then rinse wellTest a small hidden patch first
OilNeat washing-up liquid with a stiff brush, 10 minutes, then jet washSpeed matters; never petrol or solvent
Tyre marksPressure washing, a tyre mark remover or a surface cleaning machineStop turning the wheel while parked
Chewing gumFreeze spray, then a wall or paint scraperDo not dig under it with a hard edge
Cement or concrete splashesDiluted hydrochloric acid or a cement remover, rinse at onceAcid also dissolves lime-based stone
Rust-coloured spotsOxalic acid, washed off with cold water straight awayUsually iron in the stone, not something dropped
Leaf stainingSweep regularly; prevention beats cureWorst in autumn under trees

Moss and algae

Moss grows where dirt and leaves are left to sit, so the broom is the first defence. When it does take hold, brush off what you can, then treat it. Daltex points to a proprietary moss and algae killer, used as its maker says, and a strong bleach solution for ingrained algae. Addagrip treats moss and weeds with a suitable herbicide, and also uses a strong bleach solution for ingrained algae.

Here the makers differ. Daltex and Addagrip both say rinse the surface well with clean water after bleach, and Daltex leaves the moss killer to its own maker's instructions. Vuba says that for a fungicide, flushing it off may not be needed and may cut how long it keeps working, and suggests a treatment now and then as prevention on shady, damp drives. The way through is simple: bleach always gets rinsed off, and a moss killer gets whatever its own label says. Whichever you use, brush or wash off the dead growth once it has done its work.

Weeds

Weed resistant is not the same as weed free. Wind-blown seeds can sprout in dirt sitting on top, and at a weak edge. Pull small ones by hand and get the whole root out, because some weeds come back stronger if you just snap them off. Daltex says domestic weed killers on a small patch will not harm the surface. Weeds that keep coming up along one edge usually point to a gap there, which is a resin driveway repair rather than a cleaning job, and our page on driveway edging covers why edges matter.

Oil and fuel

Get to oil quickly, before it soaks in. Daltex's method is a good quality detergent, put on neat and worked in with a stiff brush, left for 10 minutes, then pressure washed. Washing-up liquid is exactly that. Another maker suggests warm water mixed with a mild household detergent. For an old stain, a biodegradable oil stain remover is the next step. What you must never do is scrub it with petrol, white spirit or any solvent: every maker warns solvents soften and damage the resin binder.

Tyre marks and scuffs

Light-coloured stone shows tyre marks most, and Addagrip says pressure washing or a tyre mark remover may be needed to shift them. The better fix is to stop making them. Vuba names the cause: turning the wheels while the car is stopped or creeping, which grinds the tyre into the surface. Roll the car as you steer, rather than turning the wheel on the spot. If you are still choosing stone, our resin driveway colours page covers how pale blends show marks.

Chewing gum, cement and rust

Gum comes off cold. Freeze it with a freeze spray, then lift it with a wall or paint scraper. Do not lever under it with a hard edge, or you will lift stone with it.

Cement or concrete splashes from building work come off with carefully used diluted hydrochloric acid or a cement remover, rinsed off straight away. Daltex warns that acid also eats into lime-based stone, so if your aggregate is limestone, try a hidden corner first and go gently. Wear gloves and eye protection with any acid.

Small rusty-orange spots that appear on their own are usually iron pyrites in the natural stone reacting with water. Daltex says oxalic acid shifts them, washed off with cold water as soon as it has done its job. If the spotting is widespread, it is a stone quality issue, which our repairs page deals with.

Stain that will not shift, or stone coming loose?

If cleaning has stopped working, tell us what the drive looks like and how big it is. We will come and look and tell you whether it needs a clean, a repair or a new surface.

What to keep off a resin driveway

Resin bound drives handle most household chemicals, but a few things do real harm, and one more thing is easy to forget: whatever you pour on a permeable drive drains through it into the ground. Vuba asks for pH-neutral cleaners where possible, biodegradable ones on permeable paving, and for any acid or alkaline cleaner to be neutralised before rinsing, to cut the risk of staining and damage to the resin.

  • Petrol, white spirit and other solvents. They soften the resin binder.
  • Strong acids used casually. Brick acid (hydrochloric) and vinegar are both acids. They have a place on specific stains, rinsed off fast, but not as a general cleaner, and never on limestone without a test.
  • Wire brushes, abrasive pads and metal scrapers. They scratch the resin and pull out stone.
  • Full-power jet washing. Stick to a fan nozzle at 150 bar or less.
  • Anything untested. Every maker says to try a new product on a small, hidden patch first.

Plain washing-up liquid is fine, and it is what the makers' oil method uses. Bleach (sodium hypochlorite) is allowed by Daltex and Addagrip for ingrained algae. Use it on the green patches only, follow the label, keep it off plants and rinse it off thoroughly.

Salt, snow and ice

You can grit a resin drive. Daltex says salt can be used to clear ice and frost, then washed off thoroughly once the weather turns. Addagrip and GCL add the catch: rock salt can harm plants and damage metal or concrete nearby, so keep it off borders, gates and concrete kerbs. Because the drive is permeable, a lot of the meltwater drains away instead of refreezing on top.

  • Clear snow with a plastic shovel, never a metal one.
  • Never use a wire brush or metal ice scraper on it.
  • If you use an eco-friendly ice melter, test a small patch first.
  • Hose the salt off once the cold snap is over.

Keeping it permeable

Resin bound drives are laid to drain, and on many front gardens that is what keeps them clear of planning permission, as our page on planning permission for a resin driveway explains. Fine silt, sand and rotted leaves can slowly fill the gaps. GCL's maintenance manual says drainage stays good with regular sweeping and suction cleaning with a wet and dry vacuum, and Daltex mentions sweepers with water jets and vacuums built in. At home, that means sweeping before it gets compacted, shovelling up any dumped sand or soil straight away, and a wet and dry vacuum over spots where puddles start to linger.

If water sits on a patch even when it is clean, the gaps there may have been closed during laying, which is a fault in the surface, not something more cleaning will fix. There is more on why drainage matters long term in how long a resin driveway lasts.

Should you seal or refresh a resin driveway?

You do not need to. None of the makers' aftercare sheets for Daltex, Vuba, Addagrip, PermaBound or SureSet lists sealing as part of looking after a resin bound drive. Sealer sellers tell a different story and suggest resealing every 3 to 5 years, but that comes from the people selling the sealer.

There is also a practical problem. A resin bound drive drains through the gaps between the stones. Anything thick enough to fill those gaps works against the drainage the drive was laid for. If you still want to use one, pick a product made for resin bound surfaces, clean and dry the drive fully first, because sealing over dirt locks it in, and try it on a hidden corner.

Refreshing a tired drive is mostly a deep clean: sweep, treat any moss, deal with the stains above, then a careful jet wash in two directions. That brings most drives back. What cleaning cannot fix is resin that has turned yellow in the sun, loose or crumbling patches, or cracks from the base moving. Those need a repair or an overlay, and the resin driveway repairs page goes through which is which.

Cleaned it and it still looks tired?

Yellowed resin, bare patches and cracks are past what a jet wash can do. Send us the size of the drive and what you are seeing, and we will quote for putting it right.

Can you jet wash during a hosepipe ban?

Pressure washing a driveway is legal in the UK. The exception is a hosepipe ban. In England and Wales, the Water Industry Act 1991 lets water companies ban cleaning paths or patios with a hosepipe, and water companies treat a pressure washer attached to a hose as part of it. Essex & Suffolk Water's notice also covers cleaning other artificial outdoor surfaces with a hosepipe. You can still use collected rainwater or reused household water, so a bucket and broom, or a washer fed from a water butt where your company allows it, will tide you over. Check your own water company's notice, because the details vary.

Resin floors, paths and bonded drives

This page is about resin bound driveways and resin bound paths, which clean the same way. A resin floor in a garage or kitchen is a solid coating with no gaps, and it is looked after differently: see how to clean and maintain a resin floor. A resin bonded drive, where loose stone is scattered onto a resin coat, is a different build too; our resin bound vs resin bonded comparison explains how to tell which you have.

About this page

Who wrote this

The Obsidian Resin team. We lay resin bound driveways anywhere in Great Britain.

Why we wrote it

Most advice on cleaning a resin drive boils down to one pressure figure. The makers' own aftercare sheets say more than that, and they do not all agree, so we have set them out side by side with the stain-by-stain methods they give. Figures come from aftercare and maintenance documents published by Derbyshire Aggregates (Daltex), Vuba, Addagrip, GCL (PermaBound) and SureSet, and from the Water Industry Act 1991 and Essex & Suffolk Water for hosepipe bans. Checked November 2026.

Our honest position

We would rather you kept your drive clean yourself than paid anyone to do it, and everything above is DIY. Where we come in is when cleaning stops working and the surface itself needs putting right, which is the point at which we quote.

Frequently asked questions

Can you jet wash a resin driveway?
Yes. The UK makers allow it with cold water, a fan nozzle, no more than 150 bar, and the lance held at least 200 mm off the surface. Vuba asks for 300 mm at about 45 degrees, moving side to side.
What is the best way to clean a resin driveway?
Sweep it with a stiff broom to clear leaves and dirt, hose it down, and only reach for a cleaner when water and a brush are not enough. Jet wash now and then on a low setting with a fan nozzle.
How do I get rid of moss on a resin driveway?
Brush off what you can, then apply a proprietary moss and algae killer as its label says. For ingrained green algae, Daltex and Addagrip allow a strong bleach solution, rinsed off well. Regular sweeping stops it coming back.
Can you use bleach (sodium hypochlorite) on a resin driveway?
Yes, for ingrained algae, according to Daltex and Addagrip. Use it as the label says, keep it to the affected patches and off plants, test a hidden area first and rinse the drive thoroughly afterwards.
Can you use washing-up liquid on a resin driveway?
Yes. A good detergent put on neat with a stiff brush, left for 10 minutes and then pressure washed is the makers' own method for oil stains.
Does vinegar clean a resin driveway?
It is an acid, so treat it like one. Vuba asks for pH-neutral cleaners on permeable drives and for any acid to be neutralised before rinsing, and acid can etch lime-based stone. Washing-up liquid and water are safer for general cleaning.
How do you get cement off a resin driveway?
Use carefully diluted hydrochloric acid or a proprietary cement remover, then rinse at once with clean water. Test a hidden area first: acid also dissolves lime-based aggregate.
How often should you jet wash a resin driveway?
No maker sets a timetable. They say clean it periodically, as often as it needs. A shady drive under trees needs it more often than an open one. Regular sweeping means you need the jet washer less.
Do you need to seal a resin driveway?
No. None of the makers' aftercare sheets we checked lists sealing as routine care. Sealer sellers suggest resealing every 3 to 5 years, but a coating that fills the gaps between the stones works against the drainage.
How do you refresh a resin driveway?
Sweep it, treat any moss, deal with stains one by one, then jet wash it carefully in two directions. If it is still yellowed, patchy or cracked after that, it needs a repair or an overlay rather than more cleaning.
Is it illegal to pressure wash a driveway in the UK?
No. But during a hosepipe ban in England and Wales, cleaning paths, patios and other outdoor surfaces with a hosepipe can be banned, and water companies count a pressure washer attached to one. Collected rainwater is allowed. Check your water company's notice.
Can I put salt on a resin driveway?
Yes. Grit it to clear ice, then wash the salt off once the weather improves. Keep rock salt off plants and nearby metal or concrete, and clear snow with a plastic shovel, never a wire brush or metal scraper.
Can I pressure wash an epoxy garage floor?
That is a different surface: a solid coating, not a permeable drive. See our page on how to clean and maintain a resin floor for how to look after it.

Read enough? Send us the space and your postcode, and get the written figure for your own floor or driveway.