A garden path that stays firm, drains and never needs raking.
Resin-bound paths, pathways and patio surrounds anywhere in Great Britain: natural stone mixed with a clear UV-stable resin and trowelled over a proper base. Firm enough for wheels, permeable, edged so it holds its line, and the same blend as a resin drive if you have one.
What you get
Firm underfoot
Even and smooth enough for wheelchairs, pushchairs, walking aids and bins, with the grip of the stone in the surface.
Rain goes through
A permeable surface over a base that drains, so no puddles along the path and no water sheeting towards the house.
Edged to hold its line
Every free edge gets a restraint in steel, aluminium, brick or stone, so the margins stay crisp and do not crumble.
Matches the drive
Laid in the same stone blend as a resin driveway, so the path, the patio surround and the drive read as one.
How it works
Tell us the route
Tell us where the path runs, roughly how long and wide it is, and what is down now: slabs, gravel, concrete or grass.
Quote in writing
One written price for the whole path, base and edging included. What we quote is what you pay.
Path laid
Dig and base where needed, fix the edging, then mix and trowel the resin-bound surface in a dry weather window.
Want a firm number? Send the size and your postcode and we come back with one written figure, not a range.
What a resin-bound path build involves
A resin-bound path is three things: a solid base, an edge, and a layer of stone held in clear resin on top. The surface you see is the thin part. For foot traffic one UK maker sets a minimum of 15mm, against 18mm for a driveway, and others go down to 12mm. Those are minimums at every point, not an average, so the base has to be flat: within 3mm under a 1m straight edge. A dip in the base becomes a thin spot in the resin.
What goes underneath depends on what is there now. A sound concrete path at least 100mm thick can usually take resin over it, with any joints carried through. A sound tarmac path can too. Where there is no hard base, or the old one is broken, we dig out and build one: a compacted open-graded sub-base such as Type 3, then a porous tarmac or concrete layer for the resin to sit on. New concrete needs around 14 days and new tarmac around 7 before the resin goes down.
Old paving slabs, block paving and loose gravel are not a base. Slabs and blocks rock and move at every joint, and gravel moves under the trowel, so the resin would crack along them. They come up, and the base is built properly underneath. Our page on what resin can be laid over goes through every existing surface.
Edging is half the job on a path
A path has far more edge for its area than a drive does: two long sides on a strip that may be under a metre wide. Every free edge of a resin-bound surface needs a restraint, or the margin crumbles where it meets the lawn or the border. Manufacturers list steel, wood, brick, stone or aluminium edging. Slim aluminium or steel strip gives a near-invisible line against grass; a brick or stone edge frames the path and can match the house. Our page on driveway edging compares the options in more depth, and every one of them works on a path too.
Firm enough for wheels, and why that matters
The building regulations define a suitable ground surface for the approach to a new home as "firm, even, smooth enough to be wheeled over, is not covered with loose laid materials such as gravel and shingle, and has a maximum crossfall of 1:40." The government lists loose gravel as not suitable for wheelchairs, and the Department for Transport says loose gravel should not be used on paths. A resin-bound path is the stone without the looseness: wheelchairs, pushchairs, walking frames, sticks, bins and heels roll and step across it rather than sinking in.
If you are replacing a gravel path for exactly this reason, our comparison of resin and gravel sets out the full trade-off.
Drainage, and the base under it
Resin-bound is permeable: rain passes down through the stone rather than lying on top. It then goes wherever the base sends it. On an open-graded sub-base it soaks into the ground. Over a solid concrete path it passes through the resin and runs across the concrete, so that base needs a fall away from the house and somewhere for the water to go. We look at that before anything else, because a path that drains towards a wall is a problem no surface can fix.
On a front garden, a permeable surface of any size needs no planning permission in England, which is part of why resin-bound suits a path to the front door. Our page on planning permission for a resin driveway covers the rule.
What a resin-bound path costs
Published UK rates put a resin-bound garden path at £90-£150 per m² as a full build, with the dig, sub-base and edging included. Over a sound existing concrete or tarmac path, where the base can stay, the going rate is £40-£70 per m². Paths often sit at the higher end per square metre for a plain reason: the set-up and the edging run are much the same as for a bigger area, spread over far fewer square metres.
Those are market figures, not our price. We send one written price for your path after we know the route, the base and the edging. Our resin driveway cost and resin patio cost pages break down what moves the number.
Paths, patio surrounds and the drive, in one blend
A path rarely stands alone. It runs from the drive to the door, round the side to the back gate, or rings a patio. Laid in the same stone blend and resin as a resin-bound driveway, the whole frontage reads as one surface, each part at the depth it needs: 18mm where cars run, 15mm where only feet do. The levels are set so water falls away from the house across the lot.
For a patio surround, the resin-bound strip can frame paving or a resin patio and stop the lawn creeping in. If what you want is a coating over an existing sound path or set of steps rather than a new stone surface, that is a different system, covered on our outdoor resin flooring page. Colours and stone blends are on our resin driveway colours and styles page.
Weather, cure and the colour that lasts
Resin-bound is laid in dry weather. Makers say not to lay when rain is expected within 24 hours, or frost, fog or dew within 48, and most systems want the air and the base above 5°C, a few down to freezing. Once laid, a path takes foot traffic after roughly 10 to 24 hours, by product and temperature.
Outdoors we use an aliphatic, UV-stable binder, which manufacturers state will not yellow in sunlight, so a pale blend stays pale. If you are thinking about doing a short path yourself, our page on a DIY resin driveway is honest about what goes wrong: a trade pedestrian kit covers only about 3.5 to 4m² at 15mm, and once mixed you have around half an hour to lay it.
What goes under a resin-bound path
The surface is the thin part. Here is what each common starting point needs before the resin goes on.
| What is there now | Can the resin go over it? | What the job involves |
|---|---|---|
| Sound concrete path, 100mm or more | Usually | Check it is sound, carry the joints through, set falls and drainage |
| Sound tarmac path | Usually | Check it is firm and drains, then lay over it |
| Paving slabs or block paving | No | Lift them, build a sub-base and bound layer |
| Loose gravel path | No | Lift the stone, build the base properly underneath |
| Grass or soil | No | Dig out, lay an open-graded sub-base and a porous bound layer, fix the edging |
Where we work
Anywhere in Great Britain
We lay resin-bound paths, pathways and patio surrounds anywhere in Great Britain. If the path runs up to a drive, our resin-bound driveways page covers that side of the job.
Resin in your city: Bristol, Newcastle, Glasgow, Manchester, London, Birmingham, Leeds, Liverpool, Sheffield, Leicester, Nottingham, Coventry, Derby, Plymouth, Bradford.
Common questions
- How much does a resin path cost?
- Published UK rates put a resin-bound garden path at £90-£150 per m² as a full build with base and edging, or £40-£70 per m² over a sound existing concrete or tarmac path. We send one written price for your path.
- How deep should a resin bound path be?
- For foot traffic, at least 12 to 15mm of resin-bound at every point, by manufacturer, against 18mm for a driveway. The minimum cannot be averaged out, so the base must be flat to within 3mm under a 1m straight edge.
- Can you lay a resin path over paving slabs?
- No. Slabs and block paving move at their joints, and the resin cracks along them. They are lifted and a proper base is built underneath. Sound concrete or tarmac can usually stay.
- Is a resin bound path good for wheelchairs?
- Yes. It is firm, even and smooth enough to wheel over, which is how the building regulations describe a suitable approach surface, and it has none of the loose stone that makes gravel hard going for wheelchairs and pushchairs.
- Does a resin path need edging?
- Yes, on every free edge. Without a restraint the margin crumbles where it meets grass or a border. Steel, aluminium, brick or stone all work.
- How long before you can walk on a resin path?
- Roughly 10 to 24 hours after laying, by product and temperature. Colder days take longer.
- Can a resin path be laid in winter?
- Only in a dry spell. Most systems need the air and the base above 5°C, a few down to freezing, with no rain due for 24 hours and no frost, fog or dew for 48.
- Do I need planning permission for a resin path?
- Not for being resin-bound. In England a permeable surface of any size in a front garden needs no planning permission, and resin-bound on a draining base is permeable.
Get your quote.
Tell us about the space and we will come back with a written quote for the whole job.