Edging is usually sold as the finishing touch on a driveway. On a resin-bound drive it is more than that: it is what holds the outer edge of a thin surface in place. This page covers every common driveway edging, what each one suits, how it is fixed, and what changes when the edge meets a lawn, a flower bed, a gravel drive or a drain.
Driveway edging options at a glance
| Edging | Look | Best for | Fixed by |
|---|---|---|---|
| Aluminium strip | Thin, near-invisible line | Resin-bound, tarmac, gravel, lawns, curves | Stakes and connectors |
| Steel strip (galvanised, painted, CorTen) | Thin line, painted or weathered finish | Gravel, lawns, beds, driveways | Stakes or formed teeth into the ground |
| Concrete kerbs or edgings | Clean, solid border | Driveways, the road edge, raised beds | Concrete bed and haunch |
| Block paving border | A framed edge in a contrasting colour | Resin and tarmac drives | Concrete bed and haunch |
| Setts or cobbles | Traditional, textured border | Period houses, drive entrances | Concrete bed and haunch |
| Brick on edge | Warm, traditional | Paths, beds, low borders | Concrete bed and haunch |
| Timber boards or sleepers | Rustic, garden feel | Gravel and bark garden paths | Treated stakes |
Every one of these can look right. The difference on a resin drive is how firmly it holds, how long it lasts, and how hard it is to replace without disturbing the resin next to it.
Why a resin driveway needs a solid edge
Resin-bound is a wearing layer, not a slab. SureSet puts it plainly: "Resin bound surface courses are generally at least 12mm in thickness therefore some form of edge restraint becomes essential." Addagrip's data sheet specifies an edging in brick, stone, concrete or steel. The general paving rule is the same: flexible pavements, tarmac included, must have an edging or kerb to stop them moving or crumbling at the edges.
In practice, the edge does three jobs. It gives the trowel something to pack the mix hard against, which the resin makers ask for on every open side. It holds the finished level. And it gives the surface a clean line where it meets a lawn, a bed or the pavement. Where kerbs are already in place, SureSet leaves the base slightly low against them to take the resin; where there are none, the edging goes in first, before any resin arrives. For the full laying process, see laying a resin driveway yourself.
Do not butt resin against a fence
Aluminium and steel edging strip
Metal strip suits resin drives because it all but disappears. SureSet describes aluminium edging as giving "a neat and distinctive finish to panels of different materials", and flexible strips can be bent to form curves.
- Aluminium: Kinley's AluExcel, made in East Sussex, is a 6005A aluminium alloy, 5 to 8.5mm thick, in heights from 18mm up to 200mm, fixed with stakes and connectors. Kinley sells it as a permanent edge for resin-bound surfacing, and for tarmac, gravel, lawns and planting beds too. An 18 or 20mm profile sits at the depth of a resin-bound surface.
- Galvanised steel: Kinley's Borderline is 2 or 3mm galvanised steel at 100 or 150mm high, made for gravel paths and heavier traffic areas such as driveways. Allow about 10% extra for the overlapping joins.
- Painted and CorTen steel: EverEdge, a British maker since 1995, offers painted, galvanised and CorTen steel, held by formed teeth driven into the ground. It is mostly lawn and border edging, also used along paths and drives.
Metal strip works best between resin and soft ground, a lawn or a bed, and between two surfaces, for example where a resin drive meets a gravel strip or a tarmac pavement. Against a public footway or where cars will run over the edge, we would use a bedded kerb or block instead.
Kerbs, block paving, setts and brick
A concrete-bedded border is the strongest edge you can give a driveway, and it is the one pavingexpert calls essential for block paving and tarmac drives. The edging units sit on a bed of concrete and are then haunched: concrete packed up the back of the unit so the drive and its traffic cannot push them out of line. The numbers from pavingexpert's specification:
| Detail | Figure |
|---|---|
| Bedding concrete | C7.5P semi-dry ("kerb mix"); site mix 6 gravel : 3 sharp sand : 1 cement |
| Haunching concrete | C20P; at least C20 for road kerbs and heavy use |
| Haunch width, driveway | 100mm minimum (75mm for a footpath) |
| Haunch height | At least half the edging depth, finished 25 to 50mm below the top |
| Bed before compacting | About 100 to 150mm |
That gives you several looks from the same method. Concrete edging kerbs make a plain, crisp border. A row of block paving in a contrasting colour frames a resin or tarmac drive. Granite setts or cobbles give a period front a traditional edge, and brick on edge suits paths and beds. One point to keep straight: setts and block paving are fine as a border, but they are not suitable as a base under resin-bound, because the joints underneath crack through. Our page on what resin can be laid over explains why, and resin against block paving compares the two as whole drives.
Planning the edge as well as the surface?
Tell us what the drive meets on each side: lawn, beds, a wall, the pavement. We will spec the edging with the resin-bound surface and put it in one written quote.
Timber edging and sleepers
Timber is easy to cut and looks at home in a garden. It is also the edging with the shortest life. pavingexpert notes that many timber edgings last only 5 to 10 years, although modern treated timber is sold with guaranteed lifespans of up to 25 years. Use preservative-treated timber, ideally tanalised, with stakes of at least 40 × 40mm driven 250mm or more into the ground about a metre apart. Gravel boards from DIY stores come in 100 and 150mm depths.
pavingexpert limits timber to garden and access paths: acceptable but not recommended on a tarmac drive, and never as the restraint for block paving. For a resin-bound drive, that and the fence warning above point the same way. Timber suits a gravel or bark path in the garden; the edge of the drive itself is better in metal, concrete or stone.
Edging a driveway next to a lawn or flower bed
Where resin meets grass, the edge has to stop the lawn creeping onto the drive and let the mower run cleanly along it. Two good options:
- Metal strip set level with the lawn: aluminium or steel, staked in, with the resin on one side and turf on the other. It gives the thinnest line and bends round curved beds.
- A mowing strip: a narrow band of paving round the lawn. pavingexpert notes these do not need building as rigidly as a structural edging, but where it also restrains the resin it should be bedded and haunched like any other border.
Beds and borders are also somewhere for water to go. In England, the government's guidance on front gardens says a drive whose rainwater runs to a lawn or border, to drain naturally, does not need planning permission even if it is impermeable. A shallow planted dip along the edge of the drive, a rain garden, does the same job, kept away from the house and on sandy or gravelly soil. Our page on planning permission for a resin driveway covers the rules.
Gravel edging for a driveway
A loose gravel drive needs edging more than any other surface, because without it the stones spread onto the lawn, the beds and the road. Galvanised steel strip at 100 or 150mm high, such as Kinley's Borderline, is made for exactly that. A bedded kerb or block border does the same job with a heavier look, and timber boards work on a garden gravel path. Where a gravel drive meets the pavement, a kerb at the entrance holds the stones back from the road. If you are weighing the two surfaces up, see resin driveway against gravel.
Drainage channels at the edge
A resin-bound drive on a permeable base lets rain soak straight through, so on many drives no channel is needed. The exceptions are where water would end up against the house, at a garage door, or where the base underneath is solid concrete that cannot drain. The government's front-garden guidance says that if a drive slopes towards the house, a drainage channel should collect the water and connect it to the drains that take the roof water. It also says not to send water towards a neighbour.
- Where they go: across a garage door threshold, at the bottom of a slope towards the house, or along the edge where the drive meets a wall.
- Load class: pavingexpert recommends at least Class B for a good domestic drain. Bargain DIY channels usually come with lighter Class A gratings, and the channel is only as strong as the weaker of the channel and its grating.
- Bedding: on a C25 concrete bed at least 100mm thick, haunched like a kerb, and laid to a fall unless the channel has one built in.
The channel then becomes the edge for that side of the resin, so set its top to the finished level before the surface goes down. Manhole covers work the same way: SureSet raises them about 10mm above the base at least 24 hours ahead, or fits recess trays, which are usually 80mm deep or more, with the top 12 to 20mm filled in resin-bound to match.
Water pooling at the house end of the drive?
Tell us which way the drive falls and what it is laid on. We will work out the base, the edge and any channel needed, and quote the full drive in writing.
Choosing the edging for your drive
Start with what the drive meets on each side, not with the look. Against a lawn or bed, metal strip gives the cleanest line. At the pavement and anywhere a wheel will run, a bedded kerb or block border holds best. Against a fence or an old timber board, put in a new edge rather than relying on the old one. At the house end of a drive that falls towards it, the edge is a channel drain. Then pick the material that suits the house. Our pages on resin driveway colours and styles and the resin-bound driveways we lay show how the border and the surface work together, and resin-bound paths covers the same edges at garden scale.
About this page
Who wrote this
Edging is part of every resin-bound job we do, which is why the Obsidian Resin team wrote this page. The figures here come from resin-bound makers' data sheets and site notes (SureSet, Addagrip, DALTEX, PermaBound), edging makers' product pages (Kinley, EverEdge), the paving specifications on pavingexpert, and the government's guidance on paving front gardens.
Our honest position
We lay resin-bound surfaces, so we would like you to choose one, and edging is part of every one we quote. Every edging on this page can look good. We care most about the ones that keep a thin resin surface intact for years, which is why the strength of the edge gets as much space here as the look.
Frequently asked questions
- Does a resin driveway need edging?
- Yes. Resin-bound is only around 12 to 24mm thick, so every open side needs an edge restraint to contain it and give a clean line. Brick, stone, concrete and steel or aluminium are the usual choices.
- What is the best edging for a resin driveway?
- Aluminium or steel strip for a near-invisible line against lawns and beds, and concrete-bedded kerbs, block paving or setts where cars run over the edge or it meets the pavement. Timber is best kept to garden paths.
- Can you use aluminium edging on a resin driveway?
- Yes. Aluminium profiles are sold as a permanent edge for resin-bound surfacing. They come from 18mm high, the depth of a driveway surface, fixed with stakes, and flexible strips can be bent into curves.
- What is the best edging for a gravel driveway?
- Galvanised steel strip around 100 to 150mm high keeps loose gravel off lawns and beds. A concrete-bedded kerb or block border is stronger where the drive meets the road.
- Can I use sleepers or timber to edge a driveway?
- You can, but timber has the shortest life of any edging, often 5 to 10 years, and replacing it disturbs the surface next to it. It suits gravel and bark garden paths better than a resin-bound drive.
- How do you edge a driveway next to a lawn?
- Set aluminium or steel strip level with the turf so the mower runs along it, or lay a narrow paved mowing strip. Either stops the grass creeping onto the drive.
- Do I need a drainage channel at the edge of my driveway?
- Not always. A permeable resin-bound drive drains through. If the drive slopes towards the house, the government guidance in England is to fit a drainage channel connected to the drains that take the roof water.
- How are kerbs fixed along a driveway?
- On a concrete bed, then haunched with concrete up the back. For a driveway the haunch should be at least 100mm wide and cover at least half the depth of the kerb.