Every driveway quote is two jobs: the base you cannot see, and the surface you can. The cheap end of the market is mostly about the surface, and the expensive mistakes are almost always about the base. Below is every common UK driveway surface ranked by what it costs to have laid, what it costs to keep, and how long it lasts, followed by what a cheap quote tends to leave out and how to cut the cost without buying a drive you redo in five years.
Every driveway surface, ranked by cost per m²
| Surface | Installed cost | Rough lifespan | Upkeep |
|---|---|---|---|
| Tarmac | £40-£80 per m² | About 15 to 25 years | Low, with more serious repairs every 15 to 20 years |
| Loose gravel | £40-£100 per m² | 15 years or more, with top-ups | Raking and top-ups, £200-£500 every 2 to 3 years |
| Gravel on a grid | Gravel plus £10-£30 per m² | As gravel | Top-ups drop to every 3 to 5 years |
| Plain concrete | £60-£90 per m² | About 20 to 30 years | Low, if the crack control joints were cut |
| Resin-bound, sound existing base | £40-£70 per m² | About 15 to 25 years | A brush and a wash |
| Resin-bound, new base | Roughly £65-£115 per m² | About 15 to 25 years | A brush and a wash |
| Block paving | £70-£120 per m² | 25 years or more | Keeping the joints topped up and weeded |
| Pattern imprinted concrete | £90-£130 per m² | About 20 to 30 years, if resealed | Reseal every 3 to 5 years at £4-£15 per m² |
Every rate in that table is a supply-and-lay figure published by UK cost sites and checked in November 2026, and the gravel and tarmac rates, for example, include digging out and laying a sub-base. That matters more than any single number on the page, because it is the commonest way a comparison goes wrong: resin is often quoted at its sound-base rate and set against gravel or block paving priced with a full dig-out. Put on the same footing, a resin-bound drive on a new base sits in the upper half of the list, alongside block paving. Over a sound tarmac or concrete drive you already have, it sits in the middle.
The figures also spread. Plain concrete is the least settled: one UK cost site prices it as low as £50 per m² and another as high as £125 for a full finish. Pattern imprinted concrete has one site well below the others, at £60-£100. Treat every range as the shape of the market, and your own quote as the real number.
The cheapest options, one by one
Tarmac: cheapest hard surface
Tarmac at £40-£80 per m² is the cheapest sealed surface you can drive on, and the published rates include a full dig-out, a Type 1 sub-base, edging and two coats. It is black and lasts around 15 to 25 years, with more serious repair work expected somewhere in the 15 to 20-year range. The main catch is that it does not drain, which brings planning into it on a front garden (more on that below). Our comparison of a resin driveway and tarmac goes through it line by line.
Gravel: cheapest to lay, not always cheapest to own
Loose gravel runs £40-£100 per m² fully built. The low end is a simple level site; the published builds include the dig, a compacted MOT Type 1 sub-base, a weed membrane, edging and the stone. It drains, it needs no planning, and burglars dislike the crunch. It also moves. Gravel without an edge restraint will migrate onto the lawn, the path and the pavement, scatters or forms waves under wheels, is not suited to a steep drive, and needs topping up at intervals. One UK cost site budgets £200-£500 every two to three years for that.
A plastic grid under the stone holds it in place for an extra £10-£30 per m², and stretches the top-ups to every three to five years. It is the single best-value upgrade at the cheap end of the market. The full gravel trade-off is in resin driveway vs gravel.
Plain concrete
At £60-£90 per m², plain or brushed concrete is the cheapest of the solid poured options and lasts 20 to 30 years. It is also the plainest, and it cracks where it likes if the crack control joints are not cut in the right places. Like tarmac, it sheds water rather than letting it through.
Resin-bonded: the cheap resin, with a catch
Resin-bonded, where loose stone is scattered onto a resin coat, costs £30-£60 per m² over a sound base, well under resin-bound. It is not permeable, and the scattered stone wears off over time. Our page on resin-bound versus resin-bonded sets out why the cheaper one is rarely the right one for a drive.
Where resin-bound sits, and why
A resin-bound driveway costs £40-£70 per m² laid over a base that is already sound, the rate two UK cost guides give for the resin layer alone. If the old surface is broken and a new sub-base has to go in, add £25-£45 per m², which takes it to roughly £65-£115 per m². For a typical 60m² two-car drive the published whole-job range is £3,500-£5,500.
So resin is not a budget surface, but it is often closer to the middle than people expect, for one reason: if you already have a sound tarmac or concrete drive, it can usually be laid straight over it. The dig-out, the skips and the new sub-base, which make up much of the cost of any new drive, drop out of the job. Our resin driveway cost page has the full breakdown, and what resin can be laid over covers which existing surfaces qualify.
Day one is not the whole bill
The ranking changes once you add ten years of upkeep. Gravel at two to three-year top-ups is three to five visits in a decade, roughly £600-£2,500 on top of the build. Pattern imprinted concrete wants resealing every three to five years to keep its colour, at £4-£15 per m², which on a 60m² drive is about £240-£900 a time. Block paving has no resealing cycle, but its joints need keeping topped up and weeded. Tarmac and plain concrete sit quietly for years. A resin-bound drive asks for a brush and the occasional wash, which our page on how to clean a resin driveway covers.
Do the maths on your own drive
What a cheap driveway quote leaves out
When two quotes for the same surface are far apart, the gap is almost always underground. Here is what gets trimmed first, and what it costs you later:
- Sub-base depth. The government guidance on permeable drives describes about 150mm of compacted sub-base over a geotextile, and roughly 200mm to 250mm of construction in all. A drive laid on a thin skim of hardcore sinks and ruts under a car, whatever is on top.
- The membrane. A geotextile under the sub-base stops it sinking into the soil and helps keep weeds down. It cannot be added once the drive is down.
- Edging. Gravel with no edge restraint spreads. A resin surface with no edge strip or restraint crumbles at the margins. Our page on driveway edging covers the options.
- Joints in concrete. Plain and imprinted concrete need crack control joints cut at the right spacing. Leave them out and the slab chooses where to crack.
- Drainage. A solid surface over five square metres of front garden needs somewhere for the water to go, which is the next section.
Already got a sound drive under the old surface?
Tell us roughly how big it is and what is down now. If the base can stay, resin goes straight over it, and the dig-out drops out of the price.
The planning cost of the cheapest surfaces
In England, the rule is simple. Under the government guidance, you do not need planning permission for a new or replacement driveway of any size that uses permeable surfacing, such as gravel, permeable block paving or porous asphalt, or that runs its rainwater onto a lawn or border. Cover more than five square metres of front garden with a traditional impermeable surface that sends the water to the road, and you do.
That catches the cheap end of the list. Ordinary tarmac and plain or imprinted concrete are solid, so on a front garden they need a drainage channel, a soakaway or a fall onto a border, or a planning application. Gravel and resin-bound let the water through, so they avoid it. The rules can differ in Wales and Scotland, so check with your council there. Our page on planning permission for a resin driveway goes into the detail.
How to make a driveway cheaper without making it worse
- Keep a sound base. Resurfacing over a solid existing drive is the biggest single saving there is.
- Go permeable on a front garden, so you are not paying for drainage channels or a planning application.
- If it has to be gravel, pay for the grid and the edging. They are what stop it being a running cost.
- Cut the area rather than the spec. Two wheel tracks, or a smaller hard area with a planted border, costs less than a thinner build over the whole plot.
- Compare quotes on the same basis: same area, same base work, same edging. A low rate that leaves out the dig-out is not a cheaper drive.
Doing it yourself is the other route. Gravel is the friendliest surface for a DIYer; resin is much less forgiving, as our page on laying a DIY resin driveway explains. For the longer trade-offs between surfaces, see resin vs block paving, resin vs imprinted concrete and how long a resin driveway lasts.
Weighing resin against a cheaper surface?
Send us the size and what is there now. You will get one written price for a resin-bound drive to set against the tarmac or gravel quotes you already have.
About this page
Who wrote this
The Obsidian Resin team wrote this. We lay resin-bound driveways anywhere in Great Britain, and "what is the cheapest way to do my drive" is the question that comes before almost every resin one.
Where the numbers come from
Every cost on this page is a published UK market range, not our price. The rates come from UK cost sites, checked in November 2026, including MyJobQuote, less.co.uk, BestBuilders, Self-build and Trade2Base; the planning rule is the government's guidance on permeable surfacing of front gardens. Lifespans are the ranges those sources publish.
Our honest position
We lay resin, so we have an interest. That is why the table puts resin on the same full-build footing as everything else rather than at its kindest rate. If tarmac or gravel suits your drive and budget better, the numbers above will tell you so.
Frequently asked questions
- What is the cheapest option for a new driveway?
- Tarmac at £40-£80 per m² and gravel at £40-£100 per m², both fully built with a sub-base. Both start around £40 per m² on a simple site. Gravel needs topping up every two to three years, so over ten years tarmac can work out cheaper.
- What is the cheapest way to redo a driveway?
- Keep the base if it is sound and resurface over it. Digging out and laying a new sub-base is much of the cost of any new drive. A sound tarmac or concrete drive can usually take a new resin-bound or tarmac surface on top.
- Is it cheaper to tarmac or concrete a driveway?
- Tarmac, usually. Published UK rates are £40-£80 per m² for tarmac and £60-£90 per m² for plain concrete. Concrete tends to last longer, around 20 to 30 years against 15 to 25 for tarmac.
- What is cheaper than tarmac?
- Very little, fully built. Gravel starts at the same £40 per m² as tarmac, and costs more to keep because of top-ups. If you already have a sound base, resin-bonded over it runs £30-£60 per m², but it is not permeable and sheds stone over time.
- What is a cheaper alternative to concrete for a driveway?
- Tarmac or gravel. Both come in below plain concrete per m², and gravel has the advantage of draining, so it needs no planning permission or drainage on a front garden.
- Is a resin driveway cheaper than block paving?
- Over a sound existing base, often yes: resin-bound is £40-£70 per m² against £70-£120 per m² for block paving. With a new base the two land in much the same range.
- How do you make an inexpensive driveway that lasts?
- Spend on what is underneath: a properly compacted sub-base, a membrane and solid edging. Choose a permeable surface for a front garden so you avoid drainage or planning costs. If you choose gravel, add a stabilising grid so it stays put.